Messages

It being .030 over now is not great . Most 428 blocks need a sonic to go .040 and that's about the limit of most 428s. It being a early block also makes it one of the least valuable.

Price reduced.

Bump

Nice parts , but rules require prices for anything for sale. I see no prices on the spread sheet.

You must not be scanning over to seeing the middle and far right column of the wide spread sheet. The prices are there ,I can see them.

Ok I see it you have to download the bottom link for it to work and show the prices. Thanks Bob!

Nice parts , but rules require prices for anything for sale. I see no prices on the spread sheet.

C90E 6312 D three sheeve crank pulley. Good shape needs blasted and cleaned.
$SOLD shipped lower 48.

C8AE 10145 B low mount alternator bracket. Needs cleaned and blasted .
$135 shipped lower 48.

428 CJ aut flex plate. Good shape , two spots with some hits where the starter has got it. Should run as is , but if you want it perfect one  throw a ring gear on it. $150 shipped this side of Mississippi. All others will need to get a quote.

All parts located in middle TN.

Link for pictures . https://www.fordfe.com/428-crank-balancer-lower-alt-bracket-and-flex-plat-t169688.html

8A31 dated C60A 6394 D hump bell housing for a early 68 1/2 428 cobra jet. Nice shape no issues or repairs. Been painted blue some time back. Comes as pictured and as advertised. $sold plus the ride.

This is a very nice std bore 428 C scratch short block. Came original out of a PI car. It's dated 9m4 with no assy date stamped on it. Engine was in the original running car 30 years ago . Around that time the engine was removed and car was scrapped . I took the block to the machine shop had it all checked out . Thermo cleaned it and magged it . All things passed and looked great. Only issue to not is a very minor chip at the very bottom of one cylinder where something just kissed it but will cause no issue upon rebuild, but I have taken a photo of it. Comes with a std 1ub crank that will need turned due to flash rust from over the years and 8 C7 big bolt rods and balancer. Engine had original cam , lifters , and bearings in place, so does t appear to have ever been apart until PO removed it. Probably have timing cover and a few other pieces if that helps. $Sold picked up in middle TN or delivery to fall Columbus this Friday or early Saturday with deposit.

HEH S narrow case hipo 289 mustang toploader. Very hard to find Hipo and early Narrow case for 5 bolt block. Has two nice old repairs at the bottom of the case on each of the lower tabs. You can't hardly notice them except from the from. Nicely done repair work. Inside looks good no issues that I see . It also moves and shifts as it should. It does have a vin stamp as well . Would have came out of a K code coupe. $800.00 picked up in middle TN or can be muled to Columbus with a deposit.

66 pump sold, 68 left. Thanks Bob for the reply!

Both of these are rebuilt the 66 pump by Ron Burke, the 68 buy a old reman company and has paper work. Both have cast iron impellers. $180 shipped for each one.  66 pump is sold 68 still available.

C8AE 6312 D three grove pulley. Needs blasted and cleaned. Don't see any other real issue. $SOLD shipped lower 48.

Feb of 68 timing cover , perfect for your March or April 68 1/2 car. $SOLD shipped lower 48.

pm sent

1968 9" pinion snub er $135 shipped lower 48.

428 CJ R servo cover and piston. Someone had ground the piston down in times not sure why so had it professionally re welded and cut back to the correct size. There is some pin holes , but won't affect any thing at all. It's where the fluid has penetrated the aluminum. No other issues or repairs.$ sold  shipped lower 48 states.

Probably a little bit , seems earlier stuff sells easier also , but still good piece.