News:

SAAC Member Badges are NOW available. Make your request through saac.memberlodge.com to validate membership.

Main Menu

Cobra intake

Started by SCOTTGTK, October 19, 2024, 03:35:35 PM

Previous topic - Next topic
Print
Go Down Pages 1 2 3 4
User actions

JD

#16
October 24, 2024, 08:48:50 AM
Was trying to help show what you have, since posting was not easy.  There are many variations of small block intakes which makes it difficult to know just what someone has in terms of "correctness" and/or value.

There are others on this forum that know a lot more about these variations than I do.

I was trying to gather images of these variations and got as far as this, see attached, and was told there were many more out there and I stopped.
'67 Shelby Headlight Bucket Grommets https://www.saacforum.com/index.php?topic=254.0
'67 Shelby Lower Grille Edge Protective Strip https://www.saacforum.com/index.php?topic=1237.0

Coralsnake

#17
October 24, 2024, 08:59:24 AM
Starting to look like the ten spoke wheel chart 😉
The original Influencer, check out www.thecoralsnake.com

Bob Gaines

#18
October 24, 2024, 09:28:11 AM Last Edit: October 24, 2024, 11:16:30 AM by Bob Gaines
Yes there are others not pictured. SCOTTGTK needs to send a over head picture of his like what JD posted to Coralsnake to post.  Preferably a picture without the carburetor or gasket underneath  on it.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

Coralsnake

#19
October 24, 2024, 09:39:40 AM
Please send me pictures

Dont give up JD keep looking for them you are the best resource
The original Influencer, check out www.thecoralsnake.com

SCOTTGTK

#20
October 25, 2024, 12:59:10 PM
Thank you all... I'll do my best to get some over head shots as soon as I can. I cannot get with carb off as I'm running it.
Thanks for posting Coralsnake.... I'll continue to try and upload from my end as well.

Coralsnake

#21
October 25, 2024, 01:51:14 PM
No problem
The original Influencer, check out www.thecoralsnake.com

SCOTTGTK

#22
October 30, 2024, 09:19:36 AM
I should be able to get a pic or more to you today Coralsnake and I'm gonna attempt to post again from my end.

Coralsnake

#23
October 30, 2024, 11:58:30 AM
Standing by
The original Influencer, check out www.thecoralsnake.com

SCOTTGTK

#24
October 30, 2024, 01:46:11 PM
Just emailed to you CS... I'll now try to load from my end as well...

SCOTTGTK

#25
October 30, 2024, 01:50:17 PM
All following/contributing to this thread, thank you and be aware, these pics are not the best... best I could get at the moment.. if you "expand" on them you'll be able to see what I see... I understand looking underneath would be helpful as well, but I wont be pulling the motor for a few more months for sure... Thanks again for your thoughts!

SCOTTGTK

#26
October 30, 2024, 02:04:54 PM
HHere are 4 of 5 pics... I think... it stopped me at 4...I'll try the 5th on another post..

SCOTTGTK

#27
October 30, 2024, 02:05:25 PM
And the 5th....

Coralsnake

#28
October 30, 2024, 02:26:00 PM Last Edit: October 30, 2024, 02:42:33 PM by Coralsnake
I need to make them smaller, I will load them shortly
The original Influencer, check out www.thecoralsnake.com

SCOTTGTK

#29
October 30, 2024, 02:40:14 PM
I just tried to open one of the pics and on my end it just sends it to downloads... Don't know of that will happen to all
Print
Go Up Pages 1 2 3 4
User actions